The performance characteristics and operation precautions of pneumatic chopper type plate dividing machine are as follows:
气动铡刀式zhi分板机性能特点：
The performance characteristics of the pneumatic chopper type Zhi plate splitter are as follows
1.裁切率为dao1秒/1分割，由脚踏板气动开关控制.
The cutting rate is Dao 1s / 1, which is controlled by foot pedal pneumatic switch
2.裁切刀组为被动启动，可安全掌握裁切线及位置;裁切应力小，不易形成龟裂现象
The cutter group is passively activated, which can safely control the cutting line and position; the cutting stress is small, and it is not easy to form cracking phenomenon
3.非滚轮(轮刀，走刀)式裁切，无粉尘现象，无马达驱动，无碳粉污染.
No dust, no motor drive, no carbon powder pollution
4.非磨擦式切削，无刀具金属残留.
Non friction cutting, no tool metal residue
5.刀片使用200000/次无电力供应，故无电器产品损耗，更换之情.
Blade used 200000 times, no power supply, no loss of electrical products, replacement
6.刀具由进口公司自行设计，无须进口时效大
The cutting tool is designed by the import company, so it is not necessary to import it and has a long time effect
7.使用4-5KG的空压，无须特定切割场所;外观以防锈保养油擦拭即可。
Use 4-5kg air pressure, do not need special cutting place; the appearance can be wiped with antirust maintenance oil.
气动铡刀式分板机的操作的安全注意事项：
Safety precautions for operation of pneumatic cutter type plate splitter:
1，作业前先确认机械是否正常。在正式的开始工作前，首先要让机械试运转二分钟左右，看刀具上下运动，电路，气路等是否顺畅，一定确认OK后再开始工作。
Confirm whether the machinery is normal before operation. Before the formal start of work, first of all, let the machine run for about two minutes to see whether the tool moves up and down, whether the circuit and air circuit are smooth, and then start to work after confirming that it is OK.
2，严格按作业指导书作业，安全事故一般都是由于工作人员不规范的操作引起的，所以说使用气动铡刀式铝基板/PCB/LED分板机一定要注意操作的规范性。
Work in strict accordance with the operation instructions, safety accidents are generally caused by the non-standard operation of the staff, so the use of pneumatic knife type aluminum substrate / PCB / LED board splitter must pay attention to the standardization of operation.
3，加强工业生产的安全意识。要时时加强安全第一的工作目标，不然工作再努力，身体受到了损伤，也是得不尝失。
Strengthen the safety awareness of industrial production. We should always strengthen the work goal of safety first, otherwise, if we work hard, we will not lose our health.
4，加工时要使PCB板的V槽与直刀刀口对准对齐，这样分出来的板毛边少，刀具的磨损量也少，效率也提高了好多。
During processing, the V-groove of PCB board should be aligned with the edge of the straight knife, so as to reduce the board burr, reduce the tool wear, and improve the efficiency.
5，作业时不能将手指或其它物品放在两直刀中间。由于直刀的钢材是很锋利的，因此加工时手指或是其它杂物注意要与刀片保持一定的距离。
Do not put fingers or other objects between two straight knives during operation. As the steel of the straight knife is very sharp, it is necessary to keep a certain distance between the finger and the blade when processing.
